QScroller Class

    QWidget *w = ...;
    QScroller::grabGesture(w, QScroller::LeftMouseButtonGesture);

    QWidget *w = ...;
    QScroller *scroller = QScroller::scroller(w);
    scroller->scrollTo(QPointF(100, 100));

Member Function Documentation

[slot] void QScroller::ensureVisible(const QRectF &rect, qreal xmargin, qreal ymargin, int scrollTime)

This is an overloaded function.

This version will reach its destination position in scrollTime milliseconds.

[slot] void QScroller::ensureVisible(const QRectF &rect, qreal xmargin, qreal ymargin)

Starts scrolling so that the rectangle rect is visible inside the viewport with additional margins specified in pixels by xmargin and ymargin around the rect.

In cases where it is not possible to fit the rect plus margins inside the viewport the contents are scrolled so that as much as possible is visible from rect.

The scrolling speed is calculated so that the given position is reached after a platform-defined time span.

This function performs the actual scrolling by calling scrollTo().

See also scrollTo().

[slot] void QScroller::resendPrepareEvent()

This function resends the QScrollPrepareEvent. Calling resendPrepareEvent triggers a QScrollPrepareEvent from the scroller. This allows the receiver to re-set content position and content size while scrolling. Calling this function while in the Inactive state is useless as the prepare event is sent again before scrolling starts.

[slot] void QScroller::scrollTo(const QPointF &pos, int scrollTime)

This is an overloaded function.

This version will reach its destination position in scrollTime milliseconds.

[slot] void QScroller::scrollTo(const QPointF &pos)

Starts scrolling the widget so that point pos is at the top-left position in the viewport.

The behaviour when scrolling outside the valid scroll area is undefined. In this case the scroller might or might not overshoot.

The scrolling speed will be calculated so that the given position will be reached after a platform-defined time span.

pos is given in viewport coordinates.

See also ensureVisible().

[signal] void QScroller::scrollerPropertiesChanged(const QScrollerProperties &newProperties)

QScroller emits this signal whenever its scroller properties change. newProperties are the new scroller properties.

Note: Notifier signal for property scrollerProperties.

See also scrollerProperties.

[signal] void QScroller::stateChanged(QScroller::State newState)

QScroller emits this signal whenever the state changes. newState is the new State.

Note: Notifier signal for property state.

See also state.

[static] QList<QScroller *> QScroller::activeScrollers()

Returns an application wide list of currently active QScroller objects. Active QScroller objects are in a state() that is not QScroller::Inactive. This function is useful when writing your own gesture recognizer.

QPointF QScroller::finalPosition() const

Returns the estimated final position for the current scroll movement. Returns the current position if the scroller state is not Scrolling. The result is undefined when the scroller state is Inactive.

The target position is in pixel.

See also pixelPerMeter() and scrollTo().

[static] Qt::GestureType QScroller::grabGesture(QObject *target, QScroller::ScrollerGestureType scrollGestureType = TouchGesture)

Registers a custom scroll gesture recognizer, grabs it for the target and returns the resulting gesture type. If scrollGestureType is set to TouchGesture the gesture triggers on touch events. If it is set to one of LeftMouseButtonGesture, RightMouseButtonGesture or MiddleMouseButtonGesture it triggers on mouse events of the corresponding button.

Only one scroll gesture can be active on a single object at the same time. If you call this function twice on the same object, it will ungrab the existing gesture before grabbing the new one.

See also ungrabGesture() and grabbedGesture().

[static] Qt::GestureType QScroller::grabbedGesture(QObject *target)

Returns the gesture type currently grabbed for the target or 0 if no gesture is grabbed.

See also grabGesture() and ungrabGesture().

bool QScroller::handleInput(QScroller::Input input, const QPointF &position, qint64 timestamp = 0)

This function is used by gesture recognizers to inform the scroller about a new input event. The scroller changes its internal state() according to the input event and its attached scroller properties. The scroller doesn't distinguish between the kind of input device the event came from. Therefore the event needs to be split into the input type, a position and a milli-second timestamp. The position needs to be in the target's coordinate system.

The return value is true if the event should be consumed by the calling filter or false if the event should be forwarded to the control.

[static] bool QScroller::hasScroller(QObject *target)

Returns true if a QScroller object was already created for target; false otherwise.

See also scroller().

QPointF QScroller::pixelPerMeter() const

Returns the pixel per meter metric for the scrolled widget.

The value is reported for both the x and y axis separately by using a QPointF.

[static] QScroller *QScroller::scroller(QObject *target)

Returns the scroller for the given target. As long as the object exists this function will always return the same QScroller instance. If no QScroller exists for the target, one will implicitly be created. At no point more than one QScroller will be active on an object.

See also hasScroller() and target().

[static] const QScroller *QScroller::scroller(const QObject *target)

This is an overloaded function.

This is the const version of scroller().

void QScroller::setSnapPositionsX(const QList<qreal> &positions)

Set the snap positions for the horizontal axis to a list of positions. This overwrites all previously set snap positions and also a previously set snapping interval. Snapping can be deactivated by setting an empty list of positions.

void QScroller::setSnapPositionsX(qreal first, qreal interval)

Set the snap positions for the horizontal axis to regular spaced intervals. The first snap position is at first. The next at first + interval. This can be used to implement a list header. This overwrites all previously set snap positions and also a previously set snapping interval. Snapping can be deactivated by setting an interval of 0.0

void QScroller::setSnapPositionsY(const QList<qreal> &positions)

Set the snap positions for the vertical axis to a list of positions. This overwrites all previously set snap positions and also a previously set snapping interval. Snapping can be deactivated by setting an empty list of positions.

void QScroller::setSnapPositionsY(qreal first, qreal interval)

Set the snap positions for the vertical axis to regular spaced intervals. The first snap position is at first. The next at first + interval. This overwrites all previously set snap positions and also a previously set snapping interval. Snapping can be deactivated by setting an interval of 0.0

void QScroller::stop()

Stops the scroller and resets its state back to Inactive.

QObject *QScroller::target() const

Returns the target object of this scroller.

See also hasScroller() and scroller().

[static] void QScroller::ungrabGesture(QObject *target)

Ungrabs the gesture for the target. Does nothing if no gesture is grabbed.

See also grabGesture() and grabbedGesture().

QPointF QScroller::velocity() const

Returns the current scrolling velocity in meter per second when the state is Scrolling or Dragging. Returns a zero velocity otherwise.

The velocity is reported for both the x and y axis separately by using a QPointF.

See also pixelPerMeter().